Cisco : 350-501 Questions & Answers

SIMULATION 5
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks
Configure the IS-IS routing protocol for R1, R2, and R3 according to the topology to achieve these goals:
1. Configure HMAC-MD5 authentication for R1, R2, and R3 links that form the IS-IS adjacency using the ISIS commands on the interfaces using these parameters:
- key-chain name: AUTH_ISIS
- key ID: 2
- password: C1sc0!
2. Configure ISIS metric on R1, R2, and R3 to:
- 15 for each level on all interfaces that form adjacency on router R1
- 20 for each level on all interfaces that form adjacency on router R2
- 25 for each level on all interface that form adjacency on R3
3. Configure IS-IS route redistribution for all static routes and connected interfaces on R1, R2, and R3.

Refer to the exhibit. A network engineer must meet these requirements to provide a connects, solution:
- The customer connected to Area 2 needs to access the application in
Area 1 on the 10.10.10.0/24 subnet
- The Customer must not have access to the 20.10.30.0/24 subnet.
- The service provider must make sure that the Area 2 routing database
limits the number of IP addresses in the routing table.
Which two configurations must be implemented to meet the requirements? (Choose two)

• A. Set a tag value of 200 to match the summary address 10.0.0/16 on R2.
• B. Set a tag value of 200 to match the summary address 10.0.0./16 on R1.
• C. Apply the route map for tag 200 and teak Level 2 routes into Level 1 Area 2 on R4.
• D. Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.
• E. Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3

Refer to the exhibit. If router RA is configured as shown, which IPv4 multicast address space does it use?

• A. 239.0.0.0/8
• B. 232.0.0.0/8
• C. 224.0.0.0/8
• D. 225.0.0.0/8

Refer to the exhibit. An engineer began to configure LDP between R1 and R2, but R1 and R2 cannot yet establish an LDP TCP connection. Which additional task must be completed to finish the implementation?

• A. Configure the mpls Idp neighbor 172.16.0.1 password command on R1
• B. Configure the no mpls Idp password option 1 command on R1
• C. Configure the mpls Idp neighbor 10.0.12.1 password command on R1
• D. Configure the no mpls Idp password option 1 command on R2

SIMULATION 6
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks